 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SHOULDER ELECTRONICS CO., LTD. CERAMIC RESONATOR Data Sheet PRODUCT : CERAMIC RESONATOR MODEL NO : ZTACS....MT PREPARED : CHECKED : APPROVED : DATE : 2007-01-25 Fengyu York Http://www.shoulder.cn SHOULDER ELECTRONICS CO., LTD. 1. Scope The specification is fit for ceramic resonator 6.00-13.00MHz. 2. Part NO: ZTACS ... MT 3. No. 3-1 3.2 3.3 3.4 3.5 3.6 Electrical Characteristics Item Oscillate Frequency (MHz) Frequency Tolerance max Resonant Impedance max () Built - in Capacitance (PF) Insulate Resistance min (M) Withstanding Voltage D.C (V) 1 2 Voltage D.C Voltage max V Input Voltage max V 100 Characteristics 6.00-13.00 0.5% 30 -100 max 5 sec 3.7 6 15Vp-p 0.3% -20 ~ +80 3.8 3.9 3.10 Temp characteristics of Oscillate frequency max Operating Temp Range Storage Temp ( ) -55 ~ +85 4. Test Circuit 5V IC 1Mohm IC Output C1 X C2 IC: 1/6TC4069UBPx2 X: Ceramic Resonator C1C2: 30PF 5. Dimension 6. Physical and Environmental Characteristics No 6.1 Item Humidity Performance Requirements It shall fulfill the Keep the resonator at 40 2 and 90-95% RH for 96 4 hours. Then specifications in Table release the resonator into the room 1. condition for 1 hour prior to the measurement. Subject the resonator to vibration for 2 It shall fulfill the hours each n x,y and z axis with the specifications in Table i amplitude of 1.5mm, the frequency shall 1. be varied uniformly between the limits of 10-55Hz Drop the resonator randomly onto a It shall fulfill the concrete floor from the height of specifications in Table 100 cm 3 times. 1. Condition of Test 6.2 Vibration 6.3 Mechanical Shock 6.4 Soldering Test 6.5 Solder Ability High Temperature Exposure Low Temperature Passed through the re-flow oven under the following condition and left at room temperature for 1 hour before measurement. Temperature at surface of the Time substrate Preheat 150 5 60 10 sec. Peak 240 5 10 3 sec. Dip the resonator terminals into the solder bath at 230 5 for 3 0.5 sec. It shall fulfill the specifications in Table 1. 6.6 6.7 6.8 Temperature Cycling More than 95% of the terminal surface shall be covered. Subject the resonator to 80 5 for 96 It shall fulfill the 4 hours. Then release the resonator specifications in Table into the room conditions for 1 hour prior 1. to the measurement. Subject the resonator to -20 5 for 96 It shall fulfill the 4 hours. Then release the resonator specifications in Table into the room conditions for 1 hour prior 1. to the measurement. Subject the resonator to -20 for 30 It shall fulfill the minutes followed by a high t mperature specifications in Table e of 85 for 30 min. Cycling shall be 1. repeated 5 times with a transfer time of 15 second at the room condition for 1 hour prior to the measurement. TABLE1 Item Oscillation Frequency Change Resonant Impedance F/Fo Ro Specification 0.3% max 10 Ohm 7. 8. Packing Tape Dimension (mm) A 0.2 MG MT MX 3.8 5.0 3.4 B 0.2 7.8 4.4 4.0 C 0.3 16.0 12.0 12.0 D 0.1 7.5 5.5 5.5 1.75 8.0 4.0 2.0 1.5 1.6 10 0.3 E 0.1 F 0.1 G 0.1 H 0.1 OJ 0.1 ON 0.1 M max R max K 0.2 2.1 1.8 1.3 0.3 T 0.1 Standard Package: 1Kpcs / reel |
Price & Availability of ZTACSMT
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |